久久久久久久亚洲精,午夜久久男人的天堂,国产萝控精品小视频,黄色一级国产片a久久,日韩一二三在线观看,青青久在线视频免费视频,日韩精品 亚洲天堂,国产专区丝袜一区二区,欧美精品一区二区三区狠狠

1、使用前應先檢查機器電源電壓（380V），并有良好的接地。
Please check the supply voltage (380V) of the machine and good earthing before starting it. 
2、開機應先檢查電機是否與油泵轉向一致，開始工作前應使油泵空轉十分鐘，見機器正常后方可工作。
Check whether the engine and the oil pump run at the same direction before startup, keep the oil pump idle for 10 minutes until normal running before working. 
3、系統壓力不得超過油泵額定壓力（31.5Mpa）,出廠前已調好，用戶不必調整。
System pressure shall not exceed the rated pressure pump (31.5Mpa), the factory before the tune is good, users do not have to adjust.
4、油箱內加足符合標準的液壓油并加至油箱3/4處(約40L)，液壓油要每半年更換一次。
Enough hydraulic oil up to the standard shall be filled up in the oil tank at its 3/4 position (about 40L); and the hydraulic oil shall be replaced each half year.
5、由于各廠家生產的接頭及套皮有一定差距，在扣壓時應根據實際情況合理選用模具，及調整微調機構。
For different joints and jackets produced by producers, moulds shall be reasonably selected to crimp them according to the situations，and adjust the fine-tuning institutions
6、應根據實際情況合理選擇，點動、自動。
should be a reasonable choice based on the actual situation, automatic, semi-automatic, manual
7、保修期內如出現故障請及時與廠家聯系，用戶自己拆裝及人為損壞不在保修范圍。
Please timely contact us for any fault occurred under warranty; users’ assembly & disassembly and the damage for misusage are beyond the scope of warranty.
8、特別說明：Special Note
（1）接通電源，點動、自動液壓起動按鈕，看電機轉向、油泵是否供油，如轉向不對，則反接電源線。
Connected to the power, point-action hydraulic starter button, watching motor steering pump is oil, such as turning right, then reverse the power cord
（2）將點動、自動按鈕旋轉至點動位置，手動按“扣合”按鈕，機器開始扣壓，至前端后再按“開模”按鈕，退回原位，反復幾次。
Will be manual, semi-automatic button to rotate to the manual position, manually click "snap" button, the machine began to withhold, to the front-end and then click "open mode" button, back in situ, repeated several times.
（3）選用合適的模具（根據標牌）調整微調機構，至扣壓出的膠管合適美觀為止。
The appropriate choice of mold (according to sign) adjustment fine-tuning body to withhold the appropriate hose out until the appearance.
（4）點動、自動的調整：
Automatic, semi-automatic, manual adjustment of
I、單件生產時，將“點動、自動”按鈕旋到“點動”位置，將裝好的管件放入模具內，按“扣壓”按鈕到合適尺寸。松開“扣壓”按鈕，按“開模”按鈕，模具打開拿出管件即可。
Single-piece production, will be "automatic, manual" button to spin to the "manual" position, will be packed into the mold tube, according to "withhold" button to the right size. Release the "withhold" button, click "open mode" button, mold can be opened out pipe.
II、小批量生產時應將“點動”按鈕旋到“自動”位置，調整微調機構，放上管件按“扣壓”按鈕進行扣壓，到前端微調機構自動發信號，進行開模，取出管件。（如扣壓的管件沒壓到尺寸，請將微調機構向外扭，使模具前移；反之相反方向調整，直到調整適合要求為止）。
Small batch production should be "automatic, manual" button to spin to the "automatic" position, adjust the fine-tuning institutions, put pipe fitting according to "withhold" button to withhold, to the front-end 
fine-tune the body automatically signals, at an open mold, remove the pipe fittings . (Such as the withholding of the pipe fittings not down to size, please fine-tune the organization has twisted, so that mold forward; the contrary the opposite direction of adjustment, adjust the fit until the required date).